Type: Driver
File Name: lexmark_x340_16917.zip
File Size: 3.9 MB
19 (4.57)
Downloads: 17
Supported systems: Windows XP (32/64-bit), Windows Vista, Windows 7, Windows 8.1, Windows 10
Price: Free* (*Free Registration Required)

Download Now

Josh-H Replied on July 24, Hi, Has this function worked in the past? Have you tried removing the printer completely?

New posts Trending Search forums. What's new. New posts New profile posts Latest activity.

Current visitors New profile posts Search profile posts Billboard Trophies. Flatbed Scanning: Yes. Film Scanning: No. If connector J1 is properly connected, verify the following voltages on the controller card. Pins 2, 4, 6, 13, 16, and 17 are ground.

If connector J4 is properly connected, verify the lexmark x340 scanner interface voltages on the controller card. Controller card If voltages are present, replace the CCD. If there are voltage irregularities, replace the controller card. Cold fuser service check Make sure the correct voltage lamp is installed. The voltage rating is stamped on one of the lamp contacts.

Lexmark X340 Multi-Function Printer Manual

FRU Action If the fuser lamp comes on and a fuser failure light error code displays, be sure the thermistor is contacting the hot roll and the thermistor cable is firmly seated in connector J15 on the controller card. Clean as necessary.

With the MFP unplugged, disconnect the thermistor cable from J15 on the controller card. Measure the resistance of the thermistor. The resistance measures from approximately 1K ohms immediately after printing or POR to approximately K ohms when thermistor reaches room temperature.

Make Your Selection

It may take 30 minutes to cool. Replace the fuser assembly as necessary.

  • Lexmark X Multi-Function Printer Manual Image Scanner Fax
  • Lexmark X Scanner Driver Download
  • Lexmark x, prints ok, but scan option wont work on windows - Microsoft Community
  • Lexmark X340-cannot get it to scan in 64 Bit 7-works perfect 32 bit
  • Question Info

Turn the MFP off, and disconnect the cooling fan cable from connector J19 on the controller card. Turn the MFP on. If voltage is present and lexmark x340 scanner interface fan is not turning, replace the cooling fan. Note: The fan speed is controlled by a module on the controller card.

Pin 1 is ground while pin 3 receives feedback from the fan motor. Verify that pin 7 on both the cable and the card connectors is ground.

Check with one probe on the connector pin and the other on the ground plane of the card found at each screw head. The CCD illuminates, and the scanner performs a calibration.

The drive motor runs. Error messages are displayed if applicable.

hp designjet 500ps plus 24Lexmark X340 Scanner Driver for Gigabyte - GA-MA785GM-US2H working on Microsoft Windows 7 Ultimate
compaq evo d51s networkAsk a Question
logicad spacemouseWhat can we do for you?

Ready is displayed on the operator panel. If immediately following power-on, the operator panel lights are active but the MFP does lexmark x340 scanner interface go through steps 1 and 2 above, replace the controller card assembly. Diagnostic information XXX Cover interlock switch service check Note: Make sure a print cartridge assembly is installed and the cover closes all the way, engaging the cover open switch lever.


Verify continuity between cable pin 1 and pin 2 with the door closed but not open. Verify continuity between cable pin 1 and pin 3 with the door open but not closed.

Specs Lexmark X Laser 25 ppm x DPI A4 Multifunctionals (20D)

Verify discontinuity between pins 2 and 3 whether the door is open or lexmark x340 scanner interface. Replace the cover interlock switch if faulty.VueScan is an application that replaces the software that came with your scanner. VueScan is compatible with the Lexmark X on Windows x86, Windows. Download the latest drivers for your Lexmark X Scanner to keep your Computer up-to-date.

Other Drivers